Price: $1,775,000ġ6” x 16” ELLICOTT SERIES 1270 DRAGON DREDGE (Ref#3877)ĥ0’ max dredging depth, 125’ swing width at minimum dreding depth, 92’ swing width at maximum dredging depth, Cat 3508 engine (1000 hp) Marine Tier 3 (heat exchanger cooled), Cat C9 auxiliary engine (350 hp) Tier 3 (radiator cooled), 1350 hp (not including standard genset), 54” cutter diameter, 29-42 rpm, 7991 lb cutting force, 18” x 66’ spuds, 98’6” overall length with ladder raised, 68’ hull length, 26’ hull width including side pontoons, 4’6” depth, (3) pontoons, ¼” and 5/16” plate thickness of center pontoon, 221,000 lbs dry weight, 2’10” hull draft (not including spuds), 6600 gallon fuel capacity. Modified gantry for longer spuds, stainless steel cutter shaft/sleeve. Standard operator cab, 6'8' with A/C and heat. Winches: (2) Swing: Pullmaster H-18, Ladder hoist: Pullmaster M-25, (2) spuds: Pullmaster H-18. Cutterhead type: 43" ID, speed 0-20rpm, 150 HP. Aux engine: CAT C-13 ACERT 440HP with Funk hydraulic drive. Main engine: CAT C-32 Acert 1125 HP (4.369 HOURS) with TwinDisc marine transmission. (2) BARGES 95’ x 31’ x 45’, without drive, with funnel, with sub-hopper discharge belt, payload 250 ton, located Europe Price: $110,000 each USDġ8” x 18” ELLICOTT SERIES 1270 DRAGON CUTTER SUCTION DREDGE (Ref#3972)īuilt 2019, 50’ max dredging depth, 54” cutter diameter, 18” x 65’ spuds, 125’ swing width at minimum dredging depth, 92’ swing width at maximum dredging depth, Cat C32 Tier 3 engine, Cat C9 auxiliary engine, operating Southeast US (8500’ dredge pipe available at extra cost) Price: $1,650,000īuilt 2012. Tabor 6 x 16 triple deck TH120 shaker screenīuilt 1975, Japan, 242’ x 45’ x 16’, payload weight 306KT, total weight 1732t, speed of shipping 8.37 kts, main generator: 1700 ps 600 rpm, propel motors power 700 kw 300 rpm, located China Price: $1,850,000īuilt 1994, 22,800 hours, 157’L x 26’W x 29’H, 91’ boom length, 40’ depth capacity, bucket volume 150 liters, delivery number 8-21/min, max capacity 350 ton/hour, diesel electric drive with electric aggregate Cat 3406T, P275T (275kva) generator, dewatering, electric wiring new, buckets newly bushed, Turas remade, chain and buckets well, located Europe Price: $375,000 USD 16" x 120’ suction was replaced with AR pipe in 2011.ġ2 x 14 GIW LSA 36 suction pump, 400 hp DC drive motorġ000kw genset p/b12V149 Detroit, 600kw genset p/b 3412 Cat, 15kw Triton genset p/b John Deere Price: $2,000,000 or best offerįLOATING SAND AND GRAVEL DREDGE (Ref#3221)Ģ006 suction dredge/process plant, constructed on a rake front hopper barge 195’ x 35’ x 12’, vessel hull was overplated with 1/4"steel plate on entire bottom, side knuckles, stern knuckles and 6’ up the sides and expoxy coated. Control house above deck house with Pitman 11000 lbs crane. 90 ton rotating crane, aft with deck house with office quarters, galley, mess deck, machine shop and storage area, hydraulic rams for positioning the after spud and an after head space, lower level with air compressors and air receiver, FO transfer pump, bilge pump, fire pump, emergency generator unit main spud Cat D398 generator. All welded, steel, hull constructed by Manitowoc, full main deck forward fitted with Page Engineering Co. Price: $3,500,000Ģ0” x 20” ELLICOTT SERIES 1870 DRAGON DREDGE (Ref#3959)īuilt 2019 (delivery 2020), excellent condition, 64’ ladder length, pump 20” x 20” x 48 p/b (2) Cat engines C32 and C15), GPS positioning, new ISO 9001 certified appraisal, located Northeast US Price: $2,790,000 Cat 3406 emergency generator set to operate the winches in case of power failure. Dredge takes 4160 volt AC power through 3000’ of 8000 volt rated cable spooled on a diesel driven barge mounted reel. Ladder hoist independent winch powered with 100 hp AC motor. 500 rpm, 3500 HP continuous 700 VDC armature, 9600 DC Digital drive system rated 3500 hp, 600 VAC input, 60 HZ, 72’ ladder plus 20’ extension, 700 hp electric over hydraulic cutterhead, 300 hp jet pump, 36” x 50’ (plus 40’ extensions) spuds hoisted by independent winch with 200 hp AC vector motors, (2) winches with 200 hp AC vector motors with 150,000# pull at 80 fpm. Built 2005, reconditioned 2009 and again in 2015, modular design of all welded steel, 133’ x 32’ x 7’ depth, 3.5’ draft (hull only), 170’ overall length, 24 x 24 HHD 62 Georgia Iron Works pump, DC motor G.E.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |